Email: info@statesidetuning.co.uk- All prices are plus VAT at 20% -
Crankcase
Crankcases
| New factory crankcases pre 1980 type, limited quantities available, a must for the serious engine builder | £799.00 |
| Used and checked crankcase - these are used cases that are chemical cleaned, hot washed + oil galley rear plugs removed, drilled and tapped to ensure correct internal cleaning of the oil galleys, main bearing journals align bored to 0.50mm. | £499.00 |
| New factory VW Type 25 80-83 crankcase. Limited quantities available. | £799.00 |
NOTE when ordering a case further machine work can be carried out eg > 911 fan cut, sleeve and bush follower bores for light weight lifter use, bore to 103mm, clearence for stroker crankshaft. Please call to discuss.
Crankcase Hardware
| Heavy duty ARP case through bolt kit, special hi-torque studs with 12 point nuts and hardend washers. | POA |
| Heavy duty ARP style cylinder stud kit, same thread as the case so no need for inserts, supplied with special nuts and washer set. Torque to 32lbs. | £255.00 per set |
| Camshaft sealing plug | £4.00 |
| 8mm stainless steel case nuts with correct wavy washer for 1 engine case | POA |
| Flywheel oil seal (German) | £14.00 |
| Fan pulley seal (German) | £6.99 |
| Oil relief piston | £6.99 |
| Oil relief spring | £4.99 |
| Oil relief screw plug | £4.20 |
| H/D oil relief piston+spring (fits on the cam bore galley) | £8.99 |
| H/D dual oil relief spring kit | £9.50 |
| Oil strainer gauze | £8.99 |
| Oil plate gasket and seal washer | £2.50 |
| Oil pick-up plate (inside the case, please state year of engine) | £30.00 |
| Oil baffle plate (original VW to stop oil surge) | From £25.00 |
| Oil baffle plate seals (4 needed) | POA |
| Clutch bolt with wave washer 7mm/11mm head used on 215 flywheels | £6.50 per set |
| Flywheel Oring seal | £3.25 |
| Flywheel felt seal | £1.45 |
| Flywheel bolt set genuine 914 Porsche longer than VW (used) | £21.00 per set |
| Crank/flywheel spigot bearing oem vw part | £7.00 |
| 7mm/11mm rocker shaft nuts and wavy washers | £5.00 per engine set |
| Thermostat cable in stainless steel | £5.90 |
| Oil dipstick bellows (fits between the housing and the case) | £3.99 |
Main Bearings
| Genuine VW Germany factory set. std x std | £109.00 |
| std x std steel backed | £69.00 |
| std x 0.25 steel backed | £69.00 |
| std x 0.50 steel backed | £69.00 |
| std x 0.75 steel backed | £79.00 |
| 0.50 x std ally backed | £69.00 |
| 0.50 x 0.25 ally backed | £69.00 |
| 0.50 x std steel backed OEM old style mahle | £139.00 |
| 0.50 x 0.25 steel backed OEM old style mahle | £139.00 |
| 0.50 x 0.50 steel backed old style OEM mahle | £139.00 |
| 1.00 x std steel backed | POA |
| 1.00 x 0.25 steel backed | POA |
NOTE oversize main bearings are available with standard flange and 1mm
Bearing Ancillaries
| Main bearing dowel locating pins | £1.00 each |
| Main bearing dowel pin (Set) | £5.00 |